Writable Wall Coverings architectural and technical information
DEP20aTransparent Dry Erase Plus Paint And Anti-Graffiti Paint
PRODUCT DESCRIPTION:
DEP20a Transparent Dry Erase Plus Paint And Anti-Graffiti Paint is a one component moisture cured polyurethane (HDI based) coating/sealer that exhibits superior characteristics for removing written markings with good UV stability for both indoor and outdoor use. Designed to remove: Dry Erase Markers, Low-odor Dry Erase Markers, Dry Erase Crayons, Permanent Markers (Sharpie), Regular Markers, Highlighters, Tape Adhesive, Crayons, Finger Paints, and Spray Paint.
RECOMMENDED FOR:
Recommended for application over smooth, cured, interior latex or enamel oil-based top-coat paint, various interior and exterior cured paints, cured cement surfaces, and other surfaces.
SOLIDS BY WEIGHT:
52% (+/- 3%)
SOLIDS BY VOLUME:
48% (+/- 3%)
VOLATILE ORGANIC CONTENT:
2.24 pounds per gallon
COLOR:
Clear (gardner 1)
RECOMMENDED FILM THICKNESS:
2 mils per coat wet thickness
COVERAGE PER GALLON:
240 square feet @ 1.5-2 mils wet thickness per brush coat for 2 coats, coverage may vary over non-smooth areaswhen sprayed and .
PACKAGING INFORMATION:
Pint, quart, 1 gallon, 5 gallon and 55 gallon containers (volumes approximate.)
STIR BEFORE EACH USE:
One component product. Thoroughly stir before use.
SHELF LIFE:
3 months in unopened container.
FINISH CHARACTERISTICS:
High gloss (>70 at 60 degrees @ Erichsen glossmeter)
ABRASION RESISTANCE:
Taber abrasor CS-17 calibrase wheel with 1000 gram total load
and 500 cycles= 4.4 mg loss
IMPACT RESISTANCE:
Gardner Impact, direct & reverse= 100 in. lb. (passed)
HARDNESS:
2H
FLEXIBILITY:
No cracks on a 1/8” mandrel
ADHESION:
360 psi @ elcometer (concrete failure, no delamination)
(applied over NP154 clear primer)
VISCOSITY:
Less than 200 cps (typical)
DOT CLASSIFICATION:
“FLAMMABLE LIQUID N.O.S, 3, UN1993, PGIII”
CURE SCHEDULE: (70°F)
recoat ……………….….20 minutes
tack free (dry to touch)…..4-7 hours
use dry erase….. ................12 hours
permanent market & regular marker …………................................7 days
APPLICATION TEMPERATURE:
50-90 degrees F with relative humidity between 60-90%
CHEMICAL RESISTANCE:
REAGENT RATING
acetic acid 5% C
xylene E
MEK B
methyl alcohol B
gasoline D
10% sodium hydroxide E
50% sodium hydroxide D
10% sulfuric D
10% hydrocholoric acid D
20% nitric acid C
ethylene glycol D
Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term
splash spill, D - 72 hour immersion, E - long term immersion. NOTE: other
chemical resistance information may be available through your sales representative.
PRIMER / UNDERCOAT:
Interior: apply directly to cured oil based paint, primer or top-coat latex paint. Also apply over other surfaces. Test small area before application.
LIMITATIONS:
*For best results use a good quality All-Purpose paint brush, a high quality low-lint low-nap roller, or an airless sprayer.
*Surface must be dry and cured prior to application. Test small area for compatibility.
*Applications in direct sunlight, high humidity or high temperatures may cause surface curing before suitable air release has occurred.
*Clarity may be affected by high humidity, low temperatures, chemical exposure or exposure to sodium vapor (or similar) lights.
*Concrete must be cured for at least 30 days.
*Concrete retaining and/or over earth requires moisture barrier.
*Substrate temperature must be 5°F above dew point.
*Use a suitable undercoat.
*If recoating after 24 hours, then the surface must be deglossed before next application.
*Physical properties are typical values and not specifications.
*See Instructions for application instructions.
*See Instructions for cleaning suggestions.
*See Instructions for limitations of our liability and warranty.
Made in the U.S.A.
Patent Pending
Product shippable in roll. Paint layer must be cured before coating. Indoor and Outdoor use.
PRODUCT DATA VALUE TEST METHOD
PHYSICAL PROPERTIES
Thickness Film: 3.0 (76) +/- 10% ASTM D 3652
mil (micron) Adhesive: 1.0-1.1 (25-28) +/- 0.1 (3)
Liner: 3.1 (79) +/- 10%
Dimensional Stability (%) MD: 0.25 On Al panel at 160 F
(71 C) for 24 hr
Widths (heights) In inches: 60, 50, 25, 10, 4, 2
Custom widths available
Lengths (in roll form) 1 foot – 200 feet
Longer lengths available
ADHESION PROPERTIES
Expected Sheer (hours) 3.0 ASTM D 3654 Method A
(1 hr dwell, 1 sq in, 4 lb load)
SERVICE TEMPERATURE RANGE -20 F to 176 F (-29 C to 80 C)
MINIMUM APPLICATION TEMPERATURE 60 F (10 C) Note: Stabilize product in environment temperature 24 hrs before application.
STORAGE STABLITY 18 Months stored at 70 F (21 C) and 50% RH
Product Performance and Suitability
All of the descriptive information, the typical performance data, and recommendations given shall be used only as a guide and do not reflect the specification or specification range for any particular property of the product. The information is merely an attempt to assist for possible use and shall not constitute any warranty implied or otherwise, guaranty, or obligation. All purchasers shall be responsible for independently determining the suitability for the installation and use of the product for the purpose intended. There are not any additional representations in addition to or contrary to the above.
WHITE SKIN GENERAL DESCRIPTION:
Flexible transparent dry erase surface on a white opaque vinyl film coated with a repositionable pressure acrylic adhesive and backed with a clear polyester release liner. Product shippable in roll. Paint layer must be cured before coating. Indoor and Outdoor use.
PRODUCT DATA VALUE TEST METHOD
PHYSICAL PROPERTIES
Thickness Film: 8.3 (211) +/- 10% ASTM D 3652
mil (micron) Adhesive: 1.0-1.1 (25-28) +/- 0.1 (3)
Liner: 1.4 (36) +/- 5%
Dimensional Stability (%) MD: 0.50 On Al panel at 160 F
TD: 0.50 (71 C) for 24 hr
Widths (heights) In inches: 60, 50, 25, 10, 4, 2
Custom widths available
Lengths (in roll form) 1 foot – 200 feet
Longer lengths available
ADHESION PROPERTIES
Expected Sheer (hours) 5.0 ASTM D 3654 Method A
(1 hr dwell, 1 sq in, 4 lb load)
Tack (gm) 270 ASTM D 2979
SERVICE TEMPERATURE RANGE -20 F to 176 F (-29 C to 80 C)
MINIMUM APPLICATION TEMPERATURE 60 F (10 C) Note: Stabilize product in environment temperature 24 hrs before application.
STORAGE STABLITY 18 Months stored at 70 F (21 C) and 50% RH
EXPECTED EXTERIOR LIFE Two years (protected edges, vented area)
Product Performance and Suitability
All of the descriptive information, the typical performance data, and recommendations given shall be used only as a guide and do not reflect the specification or specification range for any particular property of the product. The information is merely an attempt to assist for possible use and shall not constitute any warranty implied or otherwise, guaranty, or obligation. All purchasers shall be responsible for independently determining the suitability for the installation and use of the product for the purpose intended. There are not any additional representations in addition to or contrary to the above.
Product Performance and Suitability
All of the descriptive information, the typical performance data, and recommendations given shall be used only as a guide and do not reflect the specification or specification range for any particular property of the product. The information is merely an attempt to assist for possible use and shall not constitute any warranty implied or otherwise, guaranty, or obligation. All purchasers shall be responsible for independently determining the suitability for the installation and use of the product for the purpose intended. There are not any additional representations in addition to or contrary to the above
Copyright © 2011 JML Products and Design
DEP20aTransparent Dry Erase Plus Paint And Anti-Graffiti Paint
PRODUCT DESCRIPTION:
DEP20a Transparent Dry Erase Plus Paint And Anti-Graffiti Paint is a one component moisture cured polyurethane (HDI based) coating/sealer that exhibits superior characteristics for removing written markings with good UV stability for both indoor and outdoor use. Designed to remove: Dry Erase Markers, Low-odor Dry Erase Markers, Dry Erase Crayons, Permanent Markers (Sharpie), Regular Markers, Highlighters, Tape Adhesive, Crayons, Finger Paints, and Spray Paint.
RECOMMENDED FOR:
Recommended for application over smooth, cured, interior latex or enamel oil-based top-coat paint, various interior and exterior cured paints, cured cement surfaces, and other surfaces.
SOLIDS BY WEIGHT:
52% (+/- 3%)
SOLIDS BY VOLUME:
48% (+/- 3%)
VOLATILE ORGANIC CONTENT:
2.24 pounds per gallon
COLOR:
Clear (gardner 1)
RECOMMENDED FILM THICKNESS:
2 mils per coat wet thickness
COVERAGE PER GALLON:
240 square feet @ 1.5-2 mils wet thickness per brush coat for 2 coats, coverage may vary over non-smooth areaswhen sprayed and .
PACKAGING INFORMATION:
Pint, quart, 1 gallon, 5 gallon and 55 gallon containers (volumes approximate.)
STIR BEFORE EACH USE:
One component product. Thoroughly stir before use.
SHELF LIFE:
3 months in unopened container.
FINISH CHARACTERISTICS:
High gloss (>70 at 60 degrees @ Erichsen glossmeter)
ABRASION RESISTANCE:
Taber abrasor CS-17 calibrase wheel with 1000 gram total load
and 500 cycles= 4.4 mg loss
IMPACT RESISTANCE:
Gardner Impact, direct & reverse= 100 in. lb. (passed)
HARDNESS:
2H
FLEXIBILITY:
No cracks on a 1/8” mandrel
ADHESION:
360 psi @ elcometer (concrete failure, no delamination)
(applied over NP154 clear primer)
VISCOSITY:
Less than 200 cps (typical)
DOT CLASSIFICATION:
“FLAMMABLE LIQUID N.O.S, 3, UN1993, PGIII”
CURE SCHEDULE: (70°F)
recoat ……………….….20 minutes
tack free (dry to touch)…..4-7 hours
use dry erase….. ................12 hours
permanent market & regular marker …………................................7 days
APPLICATION TEMPERATURE:
50-90 degrees F with relative humidity between 60-90%
CHEMICAL RESISTANCE:
REAGENT RATING
acetic acid 5% C
xylene E
MEK B
methyl alcohol B
gasoline D
10% sodium hydroxide E
50% sodium hydroxide D
10% sulfuric D
10% hydrocholoric acid D
20% nitric acid C
ethylene glycol D
Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term
splash spill, D - 72 hour immersion, E - long term immersion. NOTE: other
chemical resistance information may be available through your sales representative.
PRIMER / UNDERCOAT:
Interior: apply directly to cured oil based paint, primer or top-coat latex paint. Also apply over other surfaces. Test small area before application.
LIMITATIONS:
*For best results use a good quality All-Purpose paint brush, a high quality low-lint low-nap roller, or an airless sprayer.
*Surface must be dry and cured prior to application. Test small area for compatibility.
*Applications in direct sunlight, high humidity or high temperatures may cause surface curing before suitable air release has occurred.
*Clarity may be affected by high humidity, low temperatures, chemical exposure or exposure to sodium vapor (or similar) lights.
*Concrete must be cured for at least 30 days.
*Concrete retaining and/or over earth requires moisture barrier.
*Substrate temperature must be 5°F above dew point.
*Use a suitable undercoat.
*If recoating after 24 hours, then the surface must be deglossed before next application.
*Physical properties are typical values and not specifications.
*See Instructions for application instructions.
*See Instructions for cleaning suggestions.
*See Instructions for limitations of our liability and warranty.
Made in the U.S.A.
Patent Pending
Product shippable in roll. Paint layer must be cured before coating. Indoor and Outdoor use.
PRODUCT DATA VALUE TEST METHOD
PHYSICAL PROPERTIES
Thickness Film: 3.0 (76) +/- 10% ASTM D 3652
mil (micron) Adhesive: 1.0-1.1 (25-28) +/- 0.1 (3)
Liner: 3.1 (79) +/- 10%
Dimensional Stability (%) MD: 0.25 On Al panel at 160 F
(71 C) for 24 hr
Widths (heights) In inches: 60, 50, 25, 10, 4, 2
Custom widths available
Lengths (in roll form) 1 foot – 200 feet
Longer lengths available
ADHESION PROPERTIES
Expected Sheer (hours) 3.0 ASTM D 3654 Method A
(1 hr dwell, 1 sq in, 4 lb load)
SERVICE TEMPERATURE RANGE -20 F to 176 F (-29 C to 80 C)
MINIMUM APPLICATION TEMPERATURE 60 F (10 C) Note: Stabilize product in environment temperature 24 hrs before application.
STORAGE STABLITY 18 Months stored at 70 F (21 C) and 50% RH
Product Performance and Suitability
All of the descriptive information, the typical performance data, and recommendations given shall be used only as a guide and do not reflect the specification or specification range for any particular property of the product. The information is merely an attempt to assist for possible use and shall not constitute any warranty implied or otherwise, guaranty, or obligation. All purchasers shall be responsible for independently determining the suitability for the installation and use of the product for the purpose intended. There are not any additional representations in addition to or contrary to the above.
WHITE SKIN GENERAL DESCRIPTION:
Flexible transparent dry erase surface on a white opaque vinyl film coated with a repositionable pressure acrylic adhesive and backed with a clear polyester release liner. Product shippable in roll. Paint layer must be cured before coating. Indoor and Outdoor use.
PRODUCT DATA VALUE TEST METHOD
PHYSICAL PROPERTIES
Thickness Film: 8.3 (211) +/- 10% ASTM D 3652
mil (micron) Adhesive: 1.0-1.1 (25-28) +/- 0.1 (3)
Liner: 1.4 (36) +/- 5%
Dimensional Stability (%) MD: 0.50 On Al panel at 160 F
TD: 0.50 (71 C) for 24 hr
Widths (heights) In inches: 60, 50, 25, 10, 4, 2
Custom widths available
Lengths (in roll form) 1 foot – 200 feet
Longer lengths available
ADHESION PROPERTIES
Expected Sheer (hours) 5.0 ASTM D 3654 Method A
(1 hr dwell, 1 sq in, 4 lb load)
Tack (gm) 270 ASTM D 2979
SERVICE TEMPERATURE RANGE -20 F to 176 F (-29 C to 80 C)
MINIMUM APPLICATION TEMPERATURE 60 F (10 C) Note: Stabilize product in environment temperature 24 hrs before application.
STORAGE STABLITY 18 Months stored at 70 F (21 C) and 50% RH
EXPECTED EXTERIOR LIFE Two years (protected edges, vented area)
Product Performance and Suitability
All of the descriptive information, the typical performance data, and recommendations given shall be used only as a guide and do not reflect the specification or specification range for any particular property of the product. The information is merely an attempt to assist for possible use and shall not constitute any warranty implied or otherwise, guaranty, or obligation. All purchasers shall be responsible for independently determining the suitability for the installation and use of the product for the purpose intended. There are not any additional representations in addition to or contrary to the above.
Product Performance and Suitability
All of the descriptive information, the typical performance data, and recommendations given shall be used only as a guide and do not reflect the specification or specification range for any particular property of the product. The information is merely an attempt to assist for possible use and shall not constitute any warranty implied or otherwise, guaranty, or obligation. All purchasers shall be responsible for independently determining the suitability for the installation and use of the product for the purpose intended. There are not any additional representations in addition to or contrary to the above
Copyright © 2011 JML Products and Design